Learning Objectives:

Today's lab will focus on logical expressions and circuits and absolute paths in the Unix operating system.

Software tools needed: web browser and Python programming environment with numpy and matplotlib packages installed.

Download the Skeletal Notes and Focus Questions to guide you while studying this lab.
These are a useful tool for note taking and you can keep these handy to study for and refer to during the final exam.

Quizzes

At the end of this lab, don't forget to take Lab Quiz 5! See the quiz page for details of the work due this week.

Using Python, Gradescope, and Blackboard

See Lab 1 for details on using Python, Gradescope, and Blackboard.

Logical Expressions

Last week, we introduced decisions (if-statements). These relied on the "test" which was an expression that evaluated to true or false.

We can build up more complicated logical expressions using built-in operators, and, or, and not. A standard way to summaries these operators is with truth tables. A truth table lists all the possible inputs and gives the output for each combination.

For example, here is the truth table for the and operator:

in1 in2 in1 and in2
TrueTrueTrue
FalseTrueFalse
TrueFalseFalse
FalseFalseFalse

It lists all the possible combinations of values for the inputs, in1 and in2 and what and would give as output. For example, if in1 is True and in2 is False, the value of in1 and in2 can be read off the last column of the third line of the truth table as False.

Similarly here is the truth table for or:
in1 in2 in1 or in2
TrueTrueTrue
FalseTrueTrue
TrueFalseTrue
FalseFalseFalse

For example, if in1 is True and in2 is False, the value of in1 or in2 can be read off the last column of the third line of the truth table as True.

The not operator changes the input from false to true, or true to false. That is, not True is false and not False is true. We can write this in the table format above:

in1 not in1
TrueFalse
FalseTrue

These logical operators are useful building complex tests for our if-statements (as well as other control structures that will be introduced later).

Snow Pack in California

As an example of logical expressions, we will use them to estimate the snow pack level in California over the last drought using satellite imagery.

Landsat Satellite Program is a joint program of USGS and NASA that has provided continuous images of the earth since 1972. The data is publicly available through the USGS-EROS site and has been invaluable in mapping changes in the earth. Today, we will use data images from the USGS remote sensing gallery:

http://remotesensing.usgs.gov/gallery/

The snow pack in the Sierra Nevada mountains provide almost a third of the water used by California. As a first estimate of snow pack, the number of pixels that are (nearly) white are counted. How much change has their been in the Sierra Nevada snowpack during the past drought in California? Here are images from before and during the worst years of the drought:
February 2011 February 2013 February 2014

How much snow is there? We will use the number of pixels that are nearly white as an estimate of the snow. We can add in a new variable, countSnow to keep track of each time a pixel is nearly white. Here's an outline of our program:

  1. Import the libraries to manipulate and display arrays.
  2. Read in the California image and store in the variable, ca.
  3. Create a new variable, countSnow, to keep track of the number of pixels that are nearly white.
  4. For each element in elevations,
  5.         If the pixel is nearly white
  6.                 countSnow = countSnow + 1
  7. Print out countSnow.

When is a pixel white? It's when the red, green, and blue values are close to 100%. In code, we would have:

t = 0.75    #Threshold for almost white-- can adjust between 0.0 and 1.0

...
for i in range(ca.shape[0]):
    for j in range(ca.shape[1]):
        if (ca[i,j,0] > t) and (ca[i,j,1] > t) and (ca[i,j,2] > t):
             countSnow = countSnow + 1
Let's translate that into Python. Open up a new IDLE window and copy over the outline. Using the image programs from last lab as a template, fill in as much as possible before looking at the program below:
#Name:  CSci 127 Teaching Staff
#Email: hunterCSci127help@gmail.com
#Date:  Fall 2017
#This program loads an image, counts the number of pixels that are
#    nearly white as an estimate for snow pack.

#Import the packages for images and arrays:
import matplotlib.pyplot as plt
import numpy as np


ca = plt.imread('CaliforniaDrought_02232011_md.png')   #Read in image
countSnow = 0            #Number of pixels that are almost white
t = 0.75                 #Threshold for almost white-- can adjust between 0.0 and 1.0

#For every pixel:
for i in range(ca.shape[0]):
     for j in range(ca.shape[1]):
          #Check if red, green, and blue are > t:
          if (ca[i,j,0] > t) and (ca[i,j,1] > t) and (ca[i,j,2] > t):
               countSnow = countSnow + 1

print("Snow count is", countSnow)

This program assumes that you have downloaded and saved CaliforniaDrought_02232011_md.png to the same directory as your program.

How can you modify your program to let the user specify the input file? See Programming Problem List.

Logical Circuits

The logical expressions above are useful not only in designing decisions and selecting data in Python, but the same concept underlies much of the hardware of computers. The and, or, and not can all be simulated in hardware via logic gates. These gates take inputs (usually 0 or 1) and output a value (0 or 1), based on the logical operator it is simulating.

These are standard symbols used to represent logic gates (with input on the left and output on the right; notice that NOT takes 1 input, AND and OR take 2):

Here is a simulator for circuits. Let's see an AND gate in action:

Try making a circuit with an OR gate:

  • Visit the CircuitVerse website and create an account if you don't have one
  • Launch the simulator (green button center-left of the CircuitVerse home page)
  • From the left hand menu under the Input pull-down, pull over two input sources (the square with the 1 inside) to the canvas. Note that once you pull it over it will contain a 0 (off).
  • Scroll down to the Gates menu, and choose the OR gate (if you don't remember which symbol that corresponds to you can hover with the mouse) and drag it over to canvas.
  • Connect the inputs to the gate by clicking and dragging the green dot of the input to that of the gate.
  • Repeat with the other input to connect it to the other input of the gate.
  • From the left menu under the Output drop-down, drag a Digital Led (the third light bulb on the top row) to the canvas.
  • Connect the output of the OR gate to the green dot on the Led.
  • Toggle (click on) the input. What happens to the red output light?

    What is different between the behavior of the OR and AND gates?

  • Majority of 3 Inputs

    Now, let's build a circuit, or collection of gates, that takes majority of 3 inputs, called in1, in2, in3:

    Log into the CircuitVerse website and launch the simulator (green button center-left of the CircuitVerse home page).
    Directions (with images) are below:

    Build your circuit as you read the instructions below:

    1. The question asks for 3 inputs-- let's use switches since those are easy to test out whether it works.
    2. We are going to need to check if any pair of inputs is True. An easy way to do this is to check that:
      • in1 and in2 are both true, or
      • in1 and in3 are both true, or
      • in2 and in3 are both true
      We can direct the signal of each input to multiple gates by dragging the green dot multiple times in different directions.
      Let's start by dragging from the Input drop-down menu 3 input switches (the square with 1 inside -- the 1 will change to 0 once you drag it to the canvas as shown below):
      .
    3. We'll build up our circuits in stages:
      • To check that in1 and in2 are both true, hook both of them up to an AND gate (in the Gates drop-down menu).
      • To check that in1 and in3 are both true, hook both of them up to another AND gate (in the Gates drop-down menu).
      • To check that in2 and in3 are both true, hook both of them up to another AND gate (in the Gates drop-down menu).

      You can check the wiring by toggling any two switches-- when you toggle the first and the second, the wires going to the first AND gate should be highlighted in bright green. Check the first and the third, and second and third as well, to make sure all is connected right.
    4. We have built each of the three bullets in our to-do list in step 2. above. The list is connected by "or", so, we need to do the same with our outputs:
      .
    5. And lastly, let's add an output light that will glow when true:
    Test the circuit you just built: Adjust your circuit until it only lights up when two switches are on.

    Translating Logical Circuits to Logical Expressions

    How do we represent this as a logical expression? Let's work backwards from the output light:

    Our last gate is an or, so we will write down an or

    	(lotsOfStuff1) or (lotsOfStuff2)
    
    We'll use parenthesis to keep things neat. Now, let's look at the left hand side (lotsOfStuff1). It also has an or, so we can write it down:
    	((lotsOfStuff3) or (lotsOfStuff4)) or (lotsOfStuff2)
    
    Let's keep refining our expressions (lotsOfStuff3) has an AND at the top, so, we will replace it with:
    	(((lotsOfStuff5) and (lotsOfStuff6)) or (lotsOfStuff4)) or (lotsOfStuff2)
    
    (lotsOfStuff5) is just a wire back to the first input, so, we can write that instead:
    	((in1 and (lotsOfStuff6)) or (lotsOfStuff4)) or (lotsOfStuff2)
    
    and similarly, (lotsOfStuff6)
    is just a wire back to the second input, so, we can write that instead:
    	((in1 and in2) or (lotsOfStuff4)) or (lotsOfStuff2)
    
    That looks better! If look at lotsOfStuff4, we see an AND gate with wires back to the first and third inputs:
    	((in1 and in2) or (in1 and in3)) or (lotsOfStuff2)
    
    Similarly, we can replace lotsOfStuff2 with:
    	((in1 and in2) or (in1 and in3)) or (in2 and in3)
    
    Double-check your parentheses to make sure they are balanced (every parenthesis that is opened is also closed and every internal operator is included in a set of parentheses).
    Save this line to a text file (you can use any text editor, just make sure to save it as plain text, with no formatting):
    #Name: Your name here
    #Email: Your email here
    #Date: 16 October 2017
    #Program #23:  Computes the majority of 3 inputs
    
    out = ((in1 and in2) or (in1 and in3)) or (in2 and in3)
    
    (your expression, preceded by out = ). For the logical expressions homework, you submit just a text file with the logical expressions. The grading script evaluates the expression, testing it with different inputs. See the Programming Problem List.

    More Exotic Gates

    In addition the AND, OR, and NOT gates, there are several other standard gates. For each, we can build a circuit using just AND, OR, and NOT gates that gives the same output.

    What does a NAND gate do?

    Toggle the inputs to figure out what the gate does.

    Now, build a circuit that has the same behavior as a nand gate (i.e. for the same inputs, both give identical output) using only AND, OR, and NOT gates.

    When you have the answer, label your inputs in1 and in2, save the answer in a file:

    #Name: Your name here
    #Email:  Your email here
    #Program:  Computes NAND of two inputs, using only AND, OR, and NOT gates
    
    out = ...
    
    (where ... is replaced by your answer). See the Programming Problem List.

    Binary Numbers

    In Lab 3 we looked at Hexadecimal numbers to represent colors.

    Another important number system in Computer Science is the Binary Number System. The digital logic design discussed above allows two voltage levels or states: false ≡ off ≡ 0 and true ≡ on ≡ 1, translating naturally into binary numbers.

    Each digit in a number has a "position". In the decimal (base 10) system to us so familiar, we know that the possible digits are 0 - 9 and each position is a power of 10. So if we see a 7 in the "ones" position we know it is 7 ones. If we see a 7 in the "tens" position we know it is 7 tens and so on. Thus, the number 77 in base 10 is 7 tens + 7 ones.

    In binary (base 2) we have two digits, 0 and 1, and each position is a power of two. In each position we can have either a 0 or a 1, so in the "ones" position we either have a 1 or not. In the "twos" position we either have a 2 or not, in the "fours" position we either have a 4 or not, and so on.

    For example, the binary number 11001 has five positions: "ones", "twos", "fours", "eights" and "sixteens" (consecutive powers of two). We have 1 only in the "ones", "eights" and "sixteens" positions, so 11001base2 = 1+8+16 = 25base10.

    Image credits: mathisfun.com

    Logic gates can thus perform logical operations on binary numbers. We can combine logic gates to do arithmetic on binary numbers: see programming problem 37.

    More on the Command Line Interface: Absolute Paths

    Last lab, we introduced relative paths for navigating the directories via the shell. Relative paths (e.g. cd ../) used the current location when executing. We can also use absolute paths that are independent of your location. For example,

    $ cd /usr/bin
    $ pwd
    $ ls
    
    will change your working directory to one of the machine's standard bin directories which is filled with programs, or binaries. The next two commands show the path to the working directory and list its contents. These binaries are in a central location to make them easier to find and use.

    Since it is nice to be able to return to your default, or home directory, there is a built-in short-cut for home (~). Try

    $ cd ~
    $ pwd
    $ ls
    
    The first command will return you to your home directory, no matter where you started.

    Next lab, we will introduce scripts, or files of shell commands, that we can execute at the command line.

    What's Next?

    You can start working on this week's programming assignments. The Programming Problem List has problem descriptions, suggested reading, and due dates next to each problem.
    Keep in mind that the due dates are one week late for flexibility (if one week there is a setback and you can't submit your programs, you will have time catch up). Still, each week you should work on the programming assignments for that week, even if they are due a week later. If you are on a roll, you are welcome to work ahead!!!